Planetagarden
Instructions
- Find a downed tree branch of your choosing, at least 4" in diameter.
- Cut your branch into approximately 1/2" slices using a saw.
- To make your base, cut one slice thicker than the coasters – around 2" - 3".
- Let your branch slices dry. ...
- Drill holes in the approximate center of each slice of wood.
- How do you seal wood slices for coasters?
- What is the best wood to make coasters out of?
- How do you preserve wood slices?
- How do you seal wood?
- How can I dry wood fast?
- How thick should wood coasters be?
- How do you make wooden coasters waterproof?
- What can I make with scrap wood?
- What is the average size of a coaster?
- How do you seal wood naturally?
- What is the best wood sealer?
- How do you finish a wooden centerpiece slice?
- Do you seal or stain wood first?
- Do I need to seal wood after staining?
- Is it OK to leave wood unfinished?
- What is the best resin to use for coasters?
- What kind of resin should I use for coasters?
- How do you keep wood from floating in resin?
How do you seal wood slices for coasters?
Instructions
- Slice branches into 1/2" thick pieces with the handsaw. Try to keep the slices as even and straight as possible.
- Sand each wood slice down using the heavy grit paper first, then the fine grit to smooth it out. Don't sand the bark.
- Wipe clean, then coat the front, back, and sides with a clear varnish.
What is the best wood to make coasters out of?
You can choose any type of wood you want. Softwoods like fir, cedar, and pine often result in a rustic look, while hardwoods like alder, beech, hickory, mahogany, maple, and oak will look more refined, and may be more durable. Look for logs that are reasonably straight, at least a foot long, and 3.5–4” in diameter.
How do you preserve wood slices?
If your wooden slice was cut and left to dry for longer than a few days, use wood sealer as a soaking solution to help prevent cracks or splits from forming. Fill the container just over halfway so you can submerge the wooden slice without overflowing the container.
How do you seal wood?
There are three surefire ways to waterproof your wood for years to come.
- Use linseed or Tung oil to create a beautiful and protective hand-rubbed finish.
- Seal the wood with coating of polyurethane, varnish, or lacquer.
- Finish and waterproof wood simultaneously with a stain-sealant combo.
How can I dry wood fast?
All you need to do is set up a decent dehumidifier beside the stack of wood to be dried, let it run, and it will suck the moisture right out of the wood. This can speed up the drying time from months or weeks to just a few days. Even better is if you add an air fan into the mix to produce some extra airflow.
How thick should wood coasters be?
To clean up the machine marks on the surface, as well as to create an even thickness, I took several passes through the planer. This brought the wood down to just under 5/8” thick. Anything between 3/8” up to 3/4” would work great for coasters.
How do you make wooden coasters waterproof?
Varnish. Varnish is an excellent material for making coasters waterproof because of its chemistry. It contains a high ratio of solids compared to other finishing solutions. You can use spar varnish to protect wood and other materials, and it's perfect for waterproofing.
What can I make with scrap wood?
100 Scrap Wood Projects to Try This Weekend to Showcase your...
- Wood Slice Cutting Board. Did a tree fall down in your yard? ...
- Pallet Wood Silverware Holder. This useful silverware holder is made from old pallets. ...
- Mason Jar Storage. ...
- Pallet Wood Toilet Paper Holder. ...
- Pallet Wall Shelf. ...
- Pallet Lamp. ...
- Scrap Wood Bench. ...
- Pallet Beer Opener.
What is the average size of a coaster?
Standard Drink Coaster Sizes: The standard sizes in North America for promotional bar or restaurant coasters are 3.5 inch and 4 inch. By far the most common size ordered are the 4 inch size.
How do you seal wood naturally?
Here are the basics:
- Step 1: Clean/Prep. Make sure your wood is sanded, dry and free of dust and debris. ...
- Step 2: Apply Tung Oil with a Natural Bristle Brush. ...
- Step 3: Wait, then Re-Oil. ...
- Step 4: Remove any Excess Oil. ...
- Step 5: Add one More Coat (the next day)
What is the best wood sealer?
Our Top Picks
- BEST OVERALL: SEAL-ONCE MARINE Penetrating Wood Sealer. ...
- EASIEST APPLICATION: Eco Advance Exterior Wood Water Repellent. ...
- BEST VALUE: Olympic Stain Smartguard Concentrated Sealant. ...
- LONGEST-LASTING SEAL: Olympic Stain Maximum Waterproofing Sealant.
How do you finish a wooden centerpiece slice?
DIY: Wood Slice Centerpieces
- Cut 1" to 1.5" thick slices from a log. ...
- Allow slices to dry for a few days.
- Sand top and bottom of slice until smooth using a variety of sandpaper grits. ...
- Apply natural colored wood stain.
- If needed, sand stain smooth with 600 grit sandpaper.
- For a glossy finish, apply Painters Touch Rust-Oleum Glossy Clear Coat finish.
Do you seal or stain wood first?
The key is to apply a thin base coat to partially seal the wood before wood staining. Sanding sealers, dewaxed shellac and wipe-on finishes will all do the trick.
Do I need to seal wood after staining?
Applying a topcoat sealer is not required, but a finish protects the stained wood from scratches and keeps it from fading over time. If applying a polyurethane finish with a brush, apply one to two coats. If using a spray can, hold 8 to 12 inches from the surface and apply two or three light coats.
Is it OK to leave wood unfinished?
If you check the relevant parts of furniture that you already owned I'm sure you'll discover examples, in solid wood as well as in plywood. Leaving wood unfinished can actually be a perfectly acceptable option even in high-humidity parts of the house like kitchens and bathrooms.
What is the best resin to use for coasters?
Silicone molds and epoxy resin are a perfect match. Because silicone is flexible, a silicone mold allows you to peel it back away from the resin cast and it will pop right back into shape, meaning you can use it over and over again. You can find silicone molds online and at most hobby and craft stores.
What kind of resin should I use for coasters?
Best Resin for Coasters – PRO MARINE SUPPLIES Art Resin
If you are looking for a durable resin that will keep your coaster (or any other DIY project) clear and glossy, then this choice by Pro Marine Supplies is ideal.
How do you keep wood from floating in resin?
Secure the wood inside the mold with glue or a screw to prevent the wood from floating when resin is added. I record wood and tinting details on the outside of the mold. This eliminates confusion if I store the resin casting for any length of time before turning it.
